How to Replace a Refrigerator Water Filter
Replacing a refrigerator water filter takes about five minutes. Here is the step-by-step process, how often to do it, and what to watch for.

You replace a refrigerator water filter by locating the filter housing inside the fridge or behind the grille, twisting or pulling the old cartridge out, and seating the new one until it locks. Then flush two to three gallons of water through the dispenser to clear air and loose carbon. The whole job takes about five minutes on most models, and you do not need any tools.
We are a Refrigerator Repair Service in Michigan, and our technicians swap filters on service calls every week. This guide walks through the exact steps, how often to change the filter, which cartridge fits your fridge, and the mistakes that lead to leaks or cloudy water.
How often should you replace a refrigerator water filter?
Most manufacturers recommend replacing the filter every six months or every 200 to 300 gallons, whichever comes first. If your fridge has a filter indicator light, it will typically turn red or amber around the six-month mark.
Michigan water throws a few curveballs. Homes on municipal supply in Detroit, Warren, and Sterling Heights usually see moderate sediment levels, so six months is a safe interval. Homes on private wells in outlying areas around Ann Arbor, Flint, and Kalamazoo often have higher iron and hardness, which clogs carbon block filters faster. In those cases, we tell customers to change the filter every four to five months.
Signs it is time to replace the filter even if the light has not come on yet:
- Water tastes flat, metallic, or like chlorine
- Ice cubes look cloudy or smell off
- Dispenser flow has slowed noticeably
- The filter is more than six months old
If you ignore the filter long enough, the cartridge stops removing contaminants and can start growing bacteria in the trapped sediment. That is when customers call us thinking the fridge is broken when the filter is the whole problem.
What you need before you start
You need the correct replacement cartridge, a towel, and about ten minutes of patience for the flush cycle. That is it.
Finding the right filter is where most people get stuck. The model number is on a sticker inside the fresh food compartment, usually on the left wall or behind the crisper drawer. Write it down and match it to the filter number on the old cartridge. Do not guess based on the fridge brand alone, because a single brand uses three or four different cartridges across its lineup.
Aftermarket filters are cheaper, but we see more complaints about them. OEM cartridges cost $35 to $70 in 2026, while generic versions run $15 to $30. The generics sometimes fit loosely and leak at the O-ring. If you want the filter to seat properly and last the full six months, stick with OEM.
If your fridge uses a built-in French Door Refrigerator Repair in Michigan style filter that sits behind the crisper drawer, the process is the same. The housing is just tucked lower.
Step-by-step refrigerator water filter replacement
Here is the exact process we use on service calls. It works on Whirlpool, GE, Samsung, LG, Frigidaire, and most other brands.
Step 1: Find the filter housing
Filter housings live in one of four places:
- Inside the fresh food compartment, upper right corner (most common)
- Behind the base grille at the bottom front of the fridge
- Inside the left or right door bin
- Behind the crisper drawer on French door models
If you cannot find it, check the owner's manual or search your model number online. It is almost always in one of those four spots.
Step 2: Turn off the water supply
Find the shutoff valve behind the fridge or under the sink and close it. This prevents a spray of water when you remove the cartridge. On most models you can skip this step because the housing has a check valve, but shutting it off is cheap insurance.
Step 3: Remove the old cartridge
Twist-style filters turn counterclockwise about a quarter turn and pull straight out. Push-button styles release when you press the button. Pull-out styles just slide free. Some cartridges drip a few ounces of water when they come out, so have the towel ready.
Step 4: Install the new cartridge
Peel the protective cap off the new filter. Line up the arrow or tab with the mark on the housing and push it in until it seats. Twist clockwise until it stops. You should feel it lock. If it does not lock, it is not seated and it will leak.
Step 5: Flush the system
Turn the water supply back on. Run the dispenser for two to three gallons, which takes about three to five minutes. The water will look gray or cloudy at first because of loose carbon dust. That is normal. Keep flushing until it runs clear.
Do not drink the first gallon. Dump it.
Step 6: Reset the filter indicator
Most fridges have a reset button on the control panel. Hold it for three seconds until the light turns green or off. On some models you hold two buttons at once. The manual tells you which.
Common mistakes and what to watch out for
The number one mistake is not flushing the new filter long enough. Customers take one sip, taste carbon, and assume the filter is defective. It is not. It just needs more flushing.
Other mistakes we see:
- Forcing a filter that does not fit. If it will not seat with light pressure, it is the wrong cartridge. Forcing it cracks the housing.
- Skipping the O-ring check. The new filter should come with a lubricated O-ring. If it is dry or missing, it will leak.
- Not resetting the indicator. The light stays on and the next person thinks the filter is still old.
- Reusing an old filter. Once it is out, it is done. Do not put it back in.
- Ignoring a slow drip after install. A drip means the filter is not seated or the O-ring is bad. Fix it now before it damages the fridge floor.
If you have a Side-by-Side Refrigerator Repair in Michigan unit with the filter in the base grille, watch for the housing door not closing all the way. That is usually a sign the cartridge is not fully seated.
When to call a professional
Call us if the new filter will not seat, if water leaks from the housing after install, or if the dispenser stops working entirely after a filter change. Those are signs of a cracked housing, a failed check valve, or a water line issue that a filter swap will not fix.
We also handle the cases where the filter is fine but the water still tastes bad. That usually points to a failing water inlet valve or a clogged line, not the filter. Our team diagnoses it in one visit.
If you have tried two filters and the water still tastes off, stop buying cartridges. Something else is wrong.
Frequently Asked Questions
How often should I replace my refrigerator water filter?
Every six months or every 200 to 300 gallons, whichever comes first. Michigan homes on well water should change it every four to five months because of higher sediment and iron levels. If the dispenser flow slows or the water tastes flat, replace it sooner.
How do I replace a refrigerator water filter?
Turn off the water supply, twist or pull the old cartridge out, seat the new one until it locks, then flush two to three gallons through the dispenser. Reset the indicator light. The whole process takes about five minutes on most models.
Can a Michigan refrigerator repair service replace my water filter?
Yes. We replace water filters on every service call and can swap yours during a routine visit. If you are already having us out for another issue, just ask and we will handle it.
What is the best refrigerator water filter for Michigan homes?
The OEM cartridge that matches your model number. Aftermarket filters cost less but fit loosely and leak more often. For well water homes, look for a carbon block filter rated for sediment and iron, and change it every four to five months.
Why does my water taste bad after replacing the filter?
You probably did not flush it long enough. New carbon filters release dust for the first two to three gallons. Run the dispenser until the water runs clear, then taste it. If it still tastes off after a full flush, the issue is likely the water line or inlet valve.
Get help with Refrigerator Repair Service in Michigan
If your filter will not seat, your dispenser is leaking, or you just want someone else to handle the swap, we can help. Our technicians serve homes across Michigan and carry common cartridges on the truck.
Call Fridge Repair Michigan at 1112223333 to schedule a visit.